PENGARUH SUDUT BEBAS PAHAT TERHADAP KEKASARAN PERMUKAAN  BAHAN ST.37 PADA PROSES PERMESINAN SEKRAP

Sriyanto Sriyanto; Edy Iryanto; Suhartoyo Suhartoyo

doi:10.31004/koloni.v1i1.17

Authors

Sriyanto Sriyanto STT WARGA SURAKARTA
Edy Iryanto Sekolah Tinggi Teknologi Warga Surakarta
Suhartoyo Suhartoyo Sekolah Tinggi Teknologi Warga Surakarta

DOI:

https://doi.org/10.31004/koloni.v1i1.17

Abstract

Metalworking for production process activities is one of the uses of metal materials for production, namely ST.37 objects because for this material the processing process is very easy and widely used. Metal working is done using a scrap machine, for the process it requires machining settings and tool geometry. Precise parameter setting, surface roughness quality as expected. The research parameters are the cutting speed and the angle of inclination of the tool. In this study, the variation of the tool angle and the cutting speed used was varied so as to produce the best variation, namely the smallest roughness value. Variations in the free angle of the cutter blade were made with variations of 5°, 10°, and 15°. Variations in machining settings were cutting speed 16 m /min,20.8m/min and 25.6m/min. With a fixed feeding depth of 0.3mm. In the initial step, the cutting chisel is sharpened with different free angle geometries, then the chisel is installed on the tool holder, put the workpiece on the vise, set the cutting speed, feeding depth, and perform the machining process. °,10° and 15° with cutting speeds of 16 m/min, 20.8 m/min and 25.6 m/min, respectively, with 3 experiments. Subsequent experimental results were averaged. For the best results with an average roughness of 4.34 m obtained from a tool angle of 15° with a cutting speed variation of 16 m/min..

Keywords: Scraping machine, chisel geometry, cutting speed, surface roughness, surface roughness tester.

References

Anrinal;, Yanto;, A., Fahmi;, H., & Darman, Y. (2020). Pengaruh Sudut Awal Pemotongan dan Kedalaman Potong Pada Proses Sekrap Terhadap Keausan Tepi Pahat HSS.pdf. Jurnal Teknik Mesin Institute Teknologi Padang, 10(2), 88–96.

Habibbullah, A., Arwizet, K., & Yufrizal, A. (2019). Pengaruh Variasi Side Clearance Angle Pahat Hss Dan Kekasaran Permukaan Benda Kerja Hasil Pembubutan Rata Pada Bahan St-60. Ranah Reseach, 2(1), 203–212.

Harahap, M. R., & Suriyanto, A. (2018). Pengaruh Kondisi Pemotongan baja Karbon SC-1045 Menggunakan Pahat HSS Terhadap Kekasaran Permukaan Pada Proses Pembubutan.pdf. PISTON, 2(2).

Ichsan;, M., A;, Y., Refdinal;, & Rifelino. (2020). Effect Variation Side Rake Angle and Depth of Cut Shapping Flat to Low Carbon Steel ST-37 Surface Roughness Value.pdf. Motivection, 2(2).

Johan;, C., & Santo. (2020). Optimasi Umur Pahat Pada Proses Pembubutan Baja ST 42.pdf. Dynamik Sain, 2(5).

Lubis;, M. S., Riza;, A., & Agung, D. P. (2020). 2020 M Sobron PENGARUH PARAMETER PEMESINAN TERHADAP KEKASARAN.pdf. Jurnal Muara Sains, 4(1), 145–153.

Napid;, S., Nasution;, A. H., & Harahap, M. R. (2022). 2022 Suhardji Napid EFEK PEMAKANAN TERHADAP KEKASARAN.pdf. Buletin Utama Teknik, 17(2).

Saleh, A. (2018). Uji Kehauasan Pahat Jenis HSS Dengan Proses Pemesinan Sekrap Menggunakan Faktorial desain Dan Algoritma Yates. TEDC, 12(2), 83–86.

Sudjatmiko;, S., & Purkuncoro, A. (2021). Analisis Pengaruh variasi Kecepatan Potong (Vc) dan Gerak Pemakanan ( F) Terhadap rasio Pemampatan Tebal Geram Tembaga Pada Proses Sekrap ( Shaper Machine). Transmisi, 17(2), 160–164.